Difference between revisions of "ICflyDisplay"

From InCircuit
Jump to: navigation, search
(General Information)
(Device Configuration)
Line 50: Line 50:
 
=== Configuration Files ===
 
=== Configuration Files ===
 
A soon as the [[ICflyDisplay]] has been started once, with microSD-card inserted, initial configuration files are stored on the card. To modify the files, remove the microSD-card from the [[ICflyDisplay]] and open the files with a text-editor on a computer. The card-socket is a push & push type. So to remove the card, you have to push it inwards first. The microSD-card should contain the config-files mentioned above. Their structure and influence on the configuration of the [[ICflyDisplay]] is described below.
 
A soon as the [[ICflyDisplay]] has been started once, with microSD-card inserted, initial configuration files are stored on the card. To modify the files, remove the microSD-card from the [[ICflyDisplay]] and open the files with a text-editor on a computer. The card-socket is a push & push type. So to remove the card, you have to push it inwards first. The microSD-card should contain the config-files mentioned above. Their structure and influence on the configuration of the [[ICflyDisplay]] is described below.
=== Airspeed ===
+
==== Airspeed ====
 
The Airspeed.txt file looks like this:
 
The Airspeed.txt file looks like this:
 
<code>  
 
<code>  
Line 71: Line 71:
 
It contains the aircraft's speed limits. Editing the values in this file results in changing the speed limits displayed in the horizon view. Refer to the Datasheet for more information about the speed limits
 
It contains the aircraft's speed limits. Editing the values in this file results in changing the speed limits displayed in the horizon view. Refer to the Datasheet for more information about the speed limits
  
=== Datachannel ===
+
==== Datachannel ====
 
The Datachannel.txt file looks like this:
 
The Datachannel.txt file looks like this:
 
<code>
 
<code>
Line 99: Line 99:
 
It contains all settings of the serial interfaces of the [[ICflyDisplay]]. Editing the values in the upper half of the file changes the baud rates of the serial interfaces. The lower half of the file selects the data sources for horizon- and motor-view. The displayed configuration sets all baud rates to '''''230400''''', the sources for horizon- and motor-data to '''''Up1''''' and '''''Up2'''''. Please notice, that only the listed values are valid.
 
It contains all settings of the serial interfaces of the [[ICflyDisplay]]. Editing the values in the upper half of the file changes the baud rates of the serial interfaces. The lower half of the file selects the data sources for horizon- and motor-view. The displayed configuration sets all baud rates to '''''230400''''', the sources for horizon- and motor-data to '''''Up1''''' and '''''Up2'''''. Please notice, that only the listed values are valid.
  
=== General ===
+
==== General ====
 
The General.txt file looks like this:
 
The General.txt file looks like this:
 
<code>
 
<code>
Line 124: Line 124:
 
It contains all general settings of the [[ICflyDisplay]]. Here the QNH-value, the display-brightness and the start window can be modified. Start Window means the mode, the display starts operating in (0 for horizon view, 1 for motor view).
 
It contains all general settings of the [[ICflyDisplay]]. Here the QNH-value, the display-brightness and the start window can be modified. Start Window means the mode, the display starts operating in (0 for horizon view, 1 for motor view).
  
=== MotorView ===
+
==== MotorView ====
  
 
The MotorView.txt file looks like this:
 
The MotorView.txt file looks like this:
Line 259: Line 259:
 
Normally you do not have to define instruments by yourself. The MotorView.txt-file contains one instrument for every data channel of the [[ICflyMotorbox 912]]. Some instruments are just set invisible. To personalize the motor view, simply make the required instruments visible by setting their '''''v'''''-value to 1 and place them in the desired location on the screen by setting the '''''px'''''- and '''''py'''''-values accordingly. The origin (0/0) of the coordinate system is located in the lower left corner of the screen.
 
Normally you do not have to define instruments by yourself. The MotorView.txt-file contains one instrument for every data channel of the [[ICflyMotorbox 912]]. Some instruments are just set invisible. To personalize the motor view, simply make the required instruments visible by setting their '''''v'''''-value to 1 and place them in the desired location on the screen by setting the '''''px'''''- and '''''py'''''-values accordingly. The origin (0/0) of the coordinate system is located in the lower left corner of the screen.
  
=== Units ===
+
==== Units ====
 
The Units.txt file looks like this:
 
The Units.txt file looks like this:
 
<code>
 
<code>

Revision as of 10:02, 15 October 2018

Contents

General Information

ICflyDisplay
ICflyDisplay

Flexible flight instrument for fixed installation

The ICflyDisplay brings the artificial horizon of the ICflyAHRSII into the cockpit. The sunlight-readable touchscreen guarantees a clear representation even in direct sunlight, as well as a simple usability. All settings are configurable via an intuitive menu operated by a high-feedback rotary encoder.

The device mode can be selected within the integraded setup menu:

  • Horizon with pressure, position and speed data are displayed in real time
  • Motor data display for the Rotax 912, (compatible with ICflyMotorbox 912)

The ICflyDisplay has 2 ICflyBus connectors that supply operating voltage and horizon- / motordata. It can be added to an existing ICfly-System easily. It is possible to operate two or more devices in a row on the same bus.


Features

  • Artificial horizon (requires ICflyAHRSII)
  • Motor data display (ICflyMotorbox912 needed)
  • ICflyBus: wired connection between ICfly devices (ICflyAHRSII, ICflyDisplay, ICflyMotorbox 912 and more)
  • Sunlight-readable display: clear presentation even in direct sunlight
  • Integrated Touchscreen & rotary encoder: configuration and selection of the operating mode directly on the device
  • Fixed installation: mounting in 80mm standard instrument cutout
  • Low power consumption of only 1.2 W

Device Configuration

The ICflyDisplay can be either configured using the internal menu or by several configuration files on the microSD-card. Up to now the ICflyDisplay supports the following configuration files.

Config-file editable values
Airspeed.txt airspeed-limits displayed in the artificial horizon view
Datachannel.txt serial interface's speeds and serial data source for horizon an motor view
General.txt QNH-value, brightness and start-window
Motorview.txt types, values and positions of the instruments of the motor view
Units.txt units of airspeed, altitude and vario

Configuration Files

A soon as the ICflyDisplay has been started once, with microSD-card inserted, initial configuration files are stored on the card. To modify the files, remove the microSD-card from the ICflyDisplay and open the files with a text-editor on a computer. The card-socket is a push & push type. So to remove the card, you have to push it inwards first. The microSD-card should contain the config-files mentioned above. Their structure and influence on the configuration of the ICflyDisplay is described below.

Airspeed

The Airspeed.txt file looks like this:

# this is a comment
# comment lines and empty lines will be ignored
# please do not insert any Spaces or tabs in the Settingline

#########################################################################################
# HorizonView Speedlimits [1/100 knots]
# example: 77.0 km/h = 41,57 knots * 1.852
# example: 41,57 knots = 77.0 km/h / 1.852   ->   4157 [1/100 knots]
Vs0:4157;
Vfe:6749;
Vs1:5345;
Vno:12688;
Vne:15118;
Va:8909;

It contains the aircraft's speed limits. Editing the values in this file results in changing the speed limits displayed in the horizon view. Refer to the Datasheet for more information about the speed limits

Datachannel

The Datachannel.txt file looks like this:

# this is a comment
# comment lines and empty lines will be ignored
# please do not insert any Spaces or tabs in the Settingline

#########################################################################################
# baudrate for Datastream
# possible values are: 1200, 4800, 9600, 19200, 38400, 57600,  115200, 230400, 256000
Up1:230400;
Up2:230400;
Dwn1:230400;
Dwn2:230400;

#########################################################################################
# source for View
# possible values are: 
# 1 = Up1 -> Upstream RX1/TX1 on female D-SUB15
# 2 = Up2 -> Upstream RX2/TX2 on female D-SUB15
# 3 = Dwn1 -> Upstream RX1/TX1 on male D-SUB15
# 4 = Dwn2 -> Upstream RX2/TX2 on male D-SUB15
Datastream Horizon:1;
Datastream Motorview:2;

It contains all settings of the serial interfaces of the ICflyDisplay. Editing the values in the upper half of the file changes the baud rates of the serial interfaces. The lower half of the file selects the data sources for horizon- and motor-view. The displayed configuration sets all baud rates to 230400, the sources for horizon- and motor-data to Up1 and Up2. Please notice, that only the listed values are valid.

General

The General.txt file looks like this:

# this is a comment
# comment lines and empty lines will be ignored
# please do not insert any Spaces or tabs in the Settingline

#########################################################################################
# QNH
QNH:1013;

#########################################################################################
# Brightness in %
# possible values are: 10, 20, 30, 40, 50, 60, 70, 80, 90, 100
Brightness:100;

#########################################################################################
# Start Window
# 0 = Horizon View
# 1 = Motor View
Displaymode:0;

It contains all general settings of the ICflyDisplay. Here the QNH-value, the display-brightness and the start window can be modified. Start Window means the mode, the display starts operating in (0 for horizon view, 1 for motor view).

MotorView

The MotorView.txt file looks like this:

# this is a comment
# comment lines and empty lines will be ignored
# please do not insert any Spaces or tabs in the Settingline

#########################################################################################
# the LCD Display has 320x/240y pixel
#
#      y-direction
#           ^
# 240 pixel |
#           +---------> x-direction
#            320 pixel

#########################################################################################
# type 1: basic Instrument
# possible names are: FuelLeft, FuelRight, FuelSum, Amps, AmbientTemp, Volts, Flaps
# size of this Element is 40x/30y pixel
# type; name; visible; position x; position y; min value green; max value green; red LED on if outside green

# 1;FuelLeft;1;80;0;5.0;60.0;1;
1;FuelLeft;1;80;0;5.0;60.0;1;

# 1;FuelRight;1;150;0;5.0;60.0;1;
1;FuelRight;1;150;0;5.0;60.0;1;

# 1;FuelSum;0;150;25;-1.0;1000.0;1;
1;FuelSum;0;150;25;-1.0;1000.0;1;

# 1;Amps;0;10;25;-5.0;15.0;1;
1;Amps;0;10;25;-5.0;15.0;1;

# 1;AmbientTemp;1;10;50;-40.0;100.0;1;
1;AmbientTemp;1;10;50;-40.0;100.0;1;

# 1;Volts;1;10;0;11.5;15.0;1;
1;Volts;1;10;0;11.5;15.0;1;

# 1;Flaps;0;80;25;-50.0;50.0;1;
1;Flaps;0;80;25;-50.0;50.0;1;

#########################################################################################
# type 2: Progressbar
# possible names are: OilTemp, OilPressure, Cyl1Temp, Cyl2Temp, Egt1Temp, Egt2Temp, FuelFlow, FuelPress
# size of this  Element is 110x/40y pixel
# type; name; visible; position x; position y; min value scala; max value scala; min value green; max value green; red LED on if outside green

# 2;OilTemp;1;210;160;30.0;130.0;50.0;110.0;1;
2;OilTemp;1;210;160;30.0;130.0;50.0;110.0;1;

# 2;OilPressure;1;210;200;0.0;7.0;2.0;5.0;1;
2;OilPressure;1;210;200;0.0;7.0;2.0;5.0;1;

# 2;Cyl1Temp;1;210;120;30.0;120.0;60.0;110.0;1;
2;Cyl1Temp;1;210;120;30.0;120.0;60.0;110.0;1;

# 2;Cyl2Temp;1;210;80;30.0;120.0;60.0;110.0;1;
2;Cyl2Temp;1;210;80;30.0;120.0;60.0;110.0;1;

# 2;Egt1Temp;0;210;80;0.0;1100.0;100.0;900.0;1;
2;Egt1Temp;0;210;80;0.0;1100.0;100.0;900.0;1;

# 2;Egt2Temp;0;210;0;0.0;1100.0;0.0;700.0;1;
2;Egt2Temp;0;210;0;0.0;1100.0;0.0;700.0;1;

# 2;FuelFlow;1;210;0;0.0;40.0;0.0;40.0;0;
2;FuelFlow;1;210;0;0.0;40.0;0.0;40.0;0;

# 2;FuelPress;1;210;40;0.0;1.0;0.0;1.0;1;
2;FuelPress;1;210;40;0.0;1.0;0.0;1.0;1;

#########################################################################################
# type 3: round Instrument
# possible names are: RPM, MAP
# size of this Element is 100x/100y pixel
# type; name; visible; position x; position y; min value scala; max value scala; start value yellow; start value red; red LED on if in red

# 3;RPM;1;5;140;1000.0;6500.0;5500.0;5800.0;1;
3;RPM;1;5;140;1000.0;6500.0;5500.0;5800.0;1;

# 3;MAP;1;100;140;10.0;32.0;28.0;30.0;1;
3;MAP;1;100;140;10.0;32.0;28.0;30.0;1;

This file defines the layout of the motor-data display. Every instrument of the the motor-data display is defined in this file. There are 3 different types of instruments:

Type Appearance Size in pixels (x/y) generated by Used for
type 1: basic instruments ICflyDisplay basic instrument.jpg 40/30 t;n;v;px;py;ming;maxg;redLED fuel-level & -flow, batterie-voltage & -current,
ambient temperature, flaps
type 2: progress bars ICflyDisplay progress bar.jpg 110/40 t;n;v;px;py;mins;maxs;ming;maxg;redLED oil-temperature & -pressure, cylinder head temperature,
exhaust gas temperature, fuel-flow & -pressure
type 3: round instruments ICflyDisplay round instrument.jpg 100/100 t;n;v;px;py;mins;maxs;starty;startr;redLED RPM, MAP (manifold pressure)

Every Instrument is generated by one line of definitions in the config-file. Every line consists of semicolon-separated values without space characters. Refer to the column generated by in the table above to see the structure needed for each type of instrument. The abbreviations stand for the following:

Abbreviation Meaning
t type of the instrument; 1 -> basic, 2 -> progress bar, 3 -> round
n name of the instrument; only the given possible names for the corresponding type are allowed
v visibility of the instrument; 1 -> visible, 0 -> not visible
px position of the instrument in x-direction
py position of the instrument in y-direction
ming minimum value of the green region of the instrument (only type 1&2, red below this value)
maxg maximum value of the green region of the instrument (only type 1&2, red above this value)
mins minimum value of the scale (only type 2&3)
maxs maximum value of the scale (only type 2&3)
starty start value of the yellow region (only type 3, green region below this value)
startr start value of the red region (only type 3, yellow region below this value)
redLED switch on red LED if value leaves the green region; 1 -> yes, 0 -> no

Normally you do not have to define instruments by yourself. The MotorView.txt-file contains one instrument for every data channel of the ICflyMotorbox 912. Some instruments are just set invisible. To personalize the motor view, simply make the required instruments visible by setting their v-value to 1 and place them in the desired location on the screen by setting the px- and py-values accordingly. The origin (0/0) of the coordinate system is located in the lower left corner of the screen.

Units

The Units.txt file looks like this:

# this is a comment
# comment lines and empty lines will be ignored
# please do not insert any Spaces or tabs in the Settingline

#########################################################################################
# Airspeed Unit
# 0 = km/h
# 1 = knots
Airspeed:0;

#########################################################################################
# Altitude Unit
# 0 = ft
# 1 = m
Altitude:0;

#########################################################################################
# Vario Unit
# 0 = ft/min
# 1 = m/s
Vario:1;

It allows changing the units of airspeed, altitude and vario in the horizon view:

  • Airspeed: 0 -> km/h, 1 -> knots
  • Altitude: 0 -> ft, 1 -> m
  • Vario: 0 -> ft/min, 1 -> m/s

Downloads

Datasheet ICflyDisplay (german)

Personal tools