ICnova AP7000 OEMplus
Contents |
Hardware
ICnova AP7000 OEMplus - with USB 2.0 high speed host
The ICnova AP7000 OEMplus is the smallest AVR32 AP7000 based linux board with an USB host interface.
A missing USB-Host on the AT32AP7000 is no hassle any more and hooking up an external hard drive or an optical drive is easily done.
This module is equipped with a huge amount of memory to realise even complex applications without memory extension.
It has 256MB NAND Flash, 64MB Mobile SD-RAM and 1MB NOR-Flash for the bootloader. The SD-RAM is connected with a 32bit wide bus to use the full performance of the AT32AP7000.
The board is ready to go and needs only a single 3.3V power supply. All Linux sources are open source and can be ordered on a CD.
By using the ICnova AP7000 OEMplus module there is no need to develop a multilayer pcb for external components. The board can be snapped easily into the matching sockets.
A free Eagle Library is in the download section available.
The ICnova AP7000 OEMplus has the following features:
- AT32AP7000 processor with up to 210DMPIS at 140MHz clock
- 64MB SDRAM
- 8MB NOR-Flash, 16 bit wide
- 256MB NAND
- internal Vreg, VIN=3.3V
- all peripherals available at connectors
- very small footprint 40mm x 35mm
- long term availability (>5 years)
Compatible evaluation boards
In-Circuit offers a wide range of evaluation boards that can be used to develop your products and solutions while reducing your development time. These evaluation boards help you to evaluate the features and performance of selected products and system solutions. Our evaluation boards demonstrate optimized and tested solutions for your application design. These boards are designed mainly for your evaluation, design and testing purposes.
The table below shows the suitable Application Development Boards (ADB) for the ICnova AP7000 OEMplus.
| Evaluation board | Main features |
|---|---|
| ADB1000 | 1x 10/100 Base-T-Ethernet-Port; 3x High-Speed-USB 2.0 ports (only with an ICnova OEMplus module); 1x USB-Device Port; connector for a TFT-Touchscreen display; 4 USART interfaces; 1x SD/MMC card reader; 2x RS485 Interfaces; Real-Time-Clock buffered with Li-Ion battery |
| ADB1001 | 2x 10/100 Base-T-Ethernet-Port; 1x High-Speed-USB 2.0 port (only with an ICnova OEMplus module); 1x USB-Device Port; 4 USART interfaces; 1x µSD card reader; Real-Time-Clock buffered with Li-Ion battery; 1x JTAG-interface (compatible with JTAGICE-mkII) |
| ADB1002 | 1x 10/100 Base-T-Ethernet-Port; 1x High-Speed-USB 2.0 Host port; 1x USB-Device Port; 1x DVI output for direct monitor support; 2x µSD card reader; 1x Real-Time-Clock buffered with Li-Ion battery; 1x JTAG-interface (compatible with JTAGICE-mkII) |
| ADB1003 | 1x 10/100 MBit Ethernet; 1x JTAG-interface; I/O Extender Board for all ICnova OEM Modules; all free pins of the OEM-Modules are routed to additional pin-headers |
| ADB1004 | 1x High-Speed-USB 2.0 Host port; 1x USB-Device Port; RS485, USART, SPI Interfaces; 1x µSD card reader; Real-Time-Clock buffered |
Software
- The Support-CD contains all sources, incl. Linux 2.6.28, which are needed to build a toolchain and a working filesystem for the ICnova-AP7000-OEM.
Downloads
Datasheet ICnova-AP7000-OEMplus
Footprint ICnova-AP7000-OEMplus
