ICnova SAM9G45 OEM

From InCircuit
Revision as of 13:47, 16 September 2014 by TBlocher (Talk | contribs)

Jump to: navigation, search

Template:Under construction


Contents

Hardware

ICnova SAM9G45 OEM - ultra small size meets highest performance

ICnova SAM9G45 OEM


By using the ICnova SAM9G45 OEM module there is no need to develop a multilayer pcb for external components. The board is ready to go and needs only a single power supply voltage of 3.3V to 5V. It can easily be snapped into the matching sockets.

The device is equipped with an Atmel AT91SAM9G45 MCU or its sister MCU Atmel AT91SAM9M10. It operates with an ARM926EJS core at 400MHz CPU clock.

A free Eagle Library is available in the downloads section.


Features:

  • Atmel ARM9 AT91SAM9G45B processor with up to 400 MHz CPU clock
  • 128MB DDR2-RAM
  • 1MB NOR-Flash
  • 256MB NAND Flash
  • 1xHigh speed (480MBit) USB Host
  • 1xHigh speed (480MBit) USB Device (configurable by software as 2nd Host)
  • Voltage regulators for 3.3V and 1.8V core voltage
  • All peripherals are accessible on connectors
  • Extreme compact design with 40x35mm overall size


The ICnova SAM9G45 OEM can be ordered at our Shop. Different Starter kits with appropriate Application Development Boards and Touchscreens are also available in the Shop


Suitable evaluation boards

In-Circuit offers a wide range of evaluation boards that can be used to develop your products and solutions while reducing your development time. These evaluation boards help you to evaluate the features and performance of selected products and system solutions. Our evaluation boards demonstrate optimized and tested solutions for your application design. These boards are designed mainly for your evaluation, design and testing purposes.

The table below shows the suitable Application Development Boards (ADB) for the ICnova SAM9G45 OEM.


Evaluation board Main features BSP
ADB1000 1x 10/100 Base-T-Ethernet-Port; 3x High-Speed-USB 2.0 ports (only with an ICnova OEMplus module); 1x USB-Device Port; connector for a TFT-Touchscreen display; 4 USART interfaces; 1x SD/MMC card reader; 2x RS485 Interfaces; Real-Time-Clock buffered with Li-Ion battery 2014.02-3.10.32
ADB1002 1x 10/100 Base-T-Ethernet-Port; 1x High-Speed-USB 2.0 Host port; 1x USB-Device Port; 1x DVI output for direct monitor support; 2x µSD card reader; 1x Real-Time-Clock buffered with Li-Ion battery; 1x JTAG-interface (compatible with JTAGICE-mkII)
ADB1003 1x 10/100 Base-T-Ethernet-Port; 1x JTAG-interface; I/O Extender Board for all ICnova OEM Modules; all free pins of the OEM-Modules are routed to additional pin-headers
ADB3000 1x 10/100 Base-T-Ethernet-Port; 1x High-Speed-USB 2.0 Host port; 1x USB-Device Port; connector for a TFT-Touchscreen display; 1x µSD card reader; USART, SPI, I2C Interfaces; 1x µSD card reader

Software

All Modules provided by In-Circuit usually have a Buildroot based system preinstalled, so they can be used out of the box. For some configuration a suitable Android-Image is provided, too.

If you are new to kernel building please refer to First Steps with Buildroot.

The Support-CD contains all sources which are needed to build a toolchain and a working filesystem for the ICnova SAM9G45 OEM. Take a look at our HowTo Category for some further information.

Downloads

Datasheet ICnova SAM9G45 OEM

Footprint ICnova SAM9G45 OEM

Gerber Footprint ICnova SAM9G45 OEM

Eagle Library ICnova SAM9G45 OEM

Pinning ICnova SAM9G45 OEM

Personal tools