|
|
Line 72: |
Line 72: |
| |} | | |} |
| | | |
− | | + | ===[[radino common problems]]=== |
− | ===Common problems and solutions=== | + | |
− | ====Uploading a sketch through the arduino IDE fails====
| + | |
− | Enable verbose output via "File->Preferences" select checkboxes "compilation" and "upload" near "Show verbose output during:"
| + | |
− | | + | |
− | Check verbose error messages during compilation and upload
| + | |
− | | + | |
− | *arduino IDE successfully finds the COM port but avrdude stops after an output like
| + | |
− | Connecting to programmer: .avrdude: Send: . [1b]
| + | |
− | avrdude: Send: S [53]
| + | |
− | avrdude: Recv:
| + | |
− | **-> Force the arduino into bootloader by pressing reset button twice when the arduino IDE starts scanning the COM ports
| + | |
− | | + | |
− | | + | |
− | *arduino IDE successfully finds the COM port but avrdude stops after an output like
| + | |
− | avrdude: ser_send(): write error: sorry no info avail
| + | |
− | **-> Force the arduino into bootloader by pressing reset button twice when the arduino IDE starts scanning the COM ports
| + | |
− | | + | |
− | | + | |
− | *arduino IDE fails after scanning the COM ports with an message like
| + | |
− | processing.app.debug.RunnerException: Couldn’t find a Leonardo on the selected port. Check that you have the correct port selected
| + | |
− | **-> Force the arduino into bootloader by pressing reset button twice when avrdude starts scanning the COM ports
| + | |
− | **-> Disconnect the arduino from USB and reconnect after some seconds
| + | |
− | **-> Maybe a restart of the arduino IDE is necessary.
| + | |
− | | + | |
− | | + | |
− | ====Windows 8 refuses to install Arduino / radino drivers====
| + | |
− | When using Windows 8, radino driver installation may be refused because of the missing digital signature.
| + | |
− | | + | |
− | | + | |
− | The following tuturial describes a possible solution to install radino drivers (hardware drivers without digital signature) properly on Windows 8:
| + | |
− | *[http://www.makeuseof.com/tag/how-can-i-install-hardware-with-unsigned-drivers-in-windows-8/ How to install hardware with unsigned drivers in Windows 8]
| + | |
− | | + | |
− | | + | |
− | Drivers for radino module and radino bootloader will be installed separately. As mentioned above, you can force your radino to enter bootloader-mode by pressing reset button twice. Your computer will then recognize your radino bootloader.
| + | |
− | | + | |
− | | + | |
− | ====radino & Linux==== | + | |
− | Some users experienced problems while trying to upload new sketches to their radino modules.
| + | |
− | A conflict with the ModemManager prevents succesful uploads. When entering bootloader-mode, the ModemManager immediately sends random data to the radino, which will prevent proper uploading.
| + | |
− | *To fix this issue, a UDEV-file can be created, located in
| + | |
− | /etc/udev/rules.d/70-modemmanager-ignore-radino.rules
| + | |
− | which holds the following content
| + | |
− | ACTION!="add|change", GOTO="ignore_radino_end"
| + | |
− | SUBSYSTEM!="usb", GOTO="ignore_radino_end"
| + | |
− | ENV{DEVTYPE}!="usb_device", GOTO="ignore_radino_end"
| + | |
− |
| + | |
− | # Ignore ICT products.
| + | |
− | ATTRS{idVendor}=="1da9", ENV{ID_MM_DEVICE_IGNORE}="1"
| + | |
− |
| + | |
− | LABEL="ignore_radino_end"
| + | |
− | The ModemManager will now ignore all In-Circuit products (like radino). You can now upload your sketches as usual, using Arduino IDE.
| + | |
− | | + | |
| | | |
| __NOTOC__ | | __NOTOC__ |
Here is an overview to our radino product family and suitable development boards.
Board |
Pictures |
Description |
Notes
|
radino nRF8001
|
|
Bluetooth v4.0 compliant, 15 GPIOS, I²C, SPI, UART, USB HID
|
|
radino WiFi
|
|
802.11 b/g/n, integrated TCP/IP protocol stack, 15 GPIOS, I²C, SPI, UART, USB HID
|
|
radino CC1101
|
|
integrated CC1101 HF frontend for 433/868/915MHz, 15 GPIOS, I²C, SPI, UART, USB HID
|
|
radino RF69
|
|
integrated RF69 HF frontend for 433/868MHz, 15 GPIOS, I²C, SPI, UART, USB HID
|
|
radino RF233
|
|
integrated RF233 HF frontend for 2.4GHz, 15 GPIOS, I²C, SPI, UART, USB HID
|
|
radino Leonardo
|
|
Carrier board suitable for all radino modules
|
|
radino Spider 2.4G
radino Spider RP-SMA
|
|
Breadboard adapter for radino WiFi and Bluetooth modules
|
|
radino USB Stick
|
|
USB Stick for radino modules
|
|
radino Watch
|
|
Battery powered wearable smart device
|
|
radino DinRail Adapter
|
|
DinRail Adapter to connect any radino Modules
|
|