Microcontroller Modules
Contents |
ICswift SAM7X128/256/512
As this product isn't developed further, no additional support can be given.
To develop custom applications on ICswift SAM7, the Tools shipped by the WinARM [1] project can be used. To program the application ATMEL's SAM-BA [2] Tools can be used.
OpenOCD:
The AT91SAM9X128, AT91SAM9X256 or AT91SAM9X512 equipped on the corresponding ICswift SAM7X128 / SAM7X256 / SAM7X512 can be debugged either using the Sam-Ba interface or using the JTAG-connector. While the further is possible only, if the flash is empty, the latter can be used to debug and program any application.
To use the JTAG-Interface any supported Adapter can be used. Using the configuration-file found at ICswift-openocd.cfg, the device can be connected running
openocd -f icswift-openocd.cfg
Downloads:
- Datasheet: Datasheet ICswift SAM7X128/256/512 (german)
- Schematic: Schematic ICswift SAM7X128/256/512
- UART Demo: ICswift UART Demo This demo shows a simple application utilizing the UART of ICswift.
- Ethernet Demo: ICswift SAM7x256 Ethernet-Demo This demo shows a simple application utilizing the Ethernet of ICswift.
The ICswift SAM7X128/256/512 can be ordered at our Shop
Micro32u4 Evalboard
The Arduino Micro is a microcontroller board based on the ATmega32u4. It has 20 digital input/output pins (of which 7 can be used as PWM outputs and 12 as analog inputs), a 16 MHz crystal oscillator, a micro USB connection, an ISP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a micro USB cable to get started. It has a form factor that enables it to be easily placed on a breadboard.
Features:
- Microcontroller: ATmega32u4
- Operating Voltage: 5V
- Operation from USB or Vin-Pin
- Input Voltage (recommended): 7-15V
- Digital I/O Pins: 20
- PWM Channels: 7
- Analog Input Channels: 12
- DC Current per I/O Pin: 40 mA
- DC Current for 3.3V Pin: 100 mA
- Flash Memory: 32 KB (ATmega32u4) of which 4 KB used by bootloader
- SRAM: 2.5 KB (ATmega32u4)
- EEPROM: 1 KB (ATmega32u4)
- Clock Speed: 16 MHz
Downloads:
- Schematic: Schematic Micro32u4 Evalboard
The Micro32u4 Evalboard can be ordered at our Shop
DIL-AT90USB162
AT90USB162 controller module
Features:
- Controller: AT90USB162
- Button for start programming via FLIP-bootloader
Downloads:
- Schematic: Schematic DIL-AT90USB162
The DIL-AT90USB162 can be ordered at our Shop
DIL-AT90USB646
Downloads:
- Schematic: Schematic DIL-AT90USB646
The DIL-AT90USB646 can be ordered at our Shop
DIL-AT90USB1287
Downloads:
- Schematic: Schematic DIL-AT90USB1287
The DIL-AT90USB1287 can be ordered at our Shop
DIL-CY8C3666AXI-052
Downloads:
- Schematic: Schematic DIL-CY8C3666AXI-052
The DIL-CY8C3666AXI-052 can be ordered at our Shop
Atmel UC3A Evaluation board
Downloads:
- Schematic: Schematic Atmel UC3A Evaluation board
The Atmel UC3A Evaluation board can be ordered at our Shop
ATxmega128A1U Centipede
The ATxmega128A1U Centipede is a breakout board with Atmel's ATxmega128A1U-AU. All Ports of the ATxmega128A1U-AU are connected to four pin rows with 2.54mm pitch. Besides there are two pads prepared for soldering an external clock.
Features:
- Atmel's ATxmega128A1U-AU integrated
- All Ports available on pin rows (2.54mm pitch)
- Dimensions: 69x69mm
- All Pins are labled with the port names of the ATxmega128A1U-AU
Downloads:
- Schematic: Schematic ATxmega128A1U Centipede
The ATxmega128A1U Centipede can be ordered at our Shop