Difference between revisions of "Microcontroller Modules"

From InCircuit
Jump to: navigation, search
(DIL-CY8C3666AXI-052)
(ICswift SAM7X128/256/512)
Line 25: Line 25:
  
 
<div style="clear:both"></div>
 
<div style="clear:both"></div>
 +
<br/><br/>
  
 
== Micro32u4 Evalboard ==
 
== Micro32u4 Evalboard ==

Revision as of 12:57, 9 February 2017

Contents

ICswift SAM7X128/256/512

ICswift SAM7X128/256/512

As this product isn't developed further, no additional support can be given.

To develop custom applications on ICswift SAM7, the Tools shipped by the WinARM [1] project can be used. To program the application ATMEL's SAM-BA [2] Tools can be used.

OpenOCD:

The AT91SAM9X128, AT91SAM9X256 or AT91SAM9X512 equipped on the corresponding ICswift SAM7X128 / SAM7X256 / SAM7X512 can be debugged either using the Sam-Ba interface or using the JTAG-connector. While the further is possible only, if the flash is empty, the latter can be used to debug and program any application.

To use the JTAG-Interface any supported Adapter can be used. Using the configuration-file found at ICswift-openocd.cfg, the device can be connected running

openocd -f icswift-openocd.cfg


Downloads:

The ICswift SAM7X128/256/512 can be ordered at our Shop



Micro32u4 Evalboard

Micro32u4 Evalboard

The Arduino Micro is a microcontroller board based on the ATmega32u4. It has 20 digital input/output pins (of which 7 can be used as PWM outputs and 12 as analog inputs), a 16 MHz crystal oscillator, a micro USB connection, an ISP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a micro USB cable to get started. It has a form factor that enables it to be easily placed on a breadboard.

Features:

  • Microcontroller: ATmega32u4
  • Operating Voltage: 5V
  • Operation from USB or Vin-Pin
  • Input Voltage (recommended): 7-15V
  • Digital I/O Pins: 20
  • PWM Channels: 7
  • Analog Input Channels: 12
  • DC Current per I/O Pin: 40 mA
  • DC Current for 3.3V Pin: 100 mA
  • Flash Memory: 32 KB (ATmega32u4) of which 4 KB used by bootloader
  • SRAM: 2.5 KB (ATmega32u4)
  • EEPROM: 1 KB (ATmega32u4)
  • Clock Speed: 16 MHz


Downloads:

The Micro32u4 Evalboard can be ordered at our Shop

DIL-AT90USB162

DIL-AT90USB162

AT90USB162 controller module


Features:

  • Controller: AT90USB162
  • Button for start programming via FLIP-bootloader


Downloads:

The DIL-AT90USB162 can be ordered at our Shop

DIL-AT90USB646

DIL-AT90USB646

AT90USB646 controller module

Features:

  • Controller: AT90USB646
  • Button for start programming via FLIP-bootloader


Downloads:

The DIL-AT90USB646 can be ordered at our Shop

DIL-AT90USB1287

DIL-AT90USB1287

AT90USB1287 controller module


Features:

  • Controller: AT90USB1287
  • The 1287 has an USB Full Speed OTG Device, so it can be used as USB-Host!
  • Button for start programming via FLIP-bootloader


Downloads:

The DIL-AT90USB1287 can be ordered at our Shop

DIL-CY8C3666AXI-052

DIL-CY8C3666AXI-052

DIL-CY8C3666AXI-052 controller module


Features:

  • Controller: CY8C3666AXI-052
  • 10-pin SWD programming connector for Cypress MiniProg3 Programmer


Downloads:

The DIL-CY8C3666AXI-052 can be ordered at our Shop

Atmel UC3A Evaluation board

File:none
Atmel UC3A Evaluation board

Downloads:

The Atmel UC3A Evaluation board can be ordered at our Shop


ATxmega128A1U Centipede

ATxmega128A1U Centipede

The ATxmega128A1U Centipede is a breakout board with Atmel's ATxmega128A1U-AU. All Ports of the ATxmega128A1U-AU are connected to four pin rows with 2.54mm pitch. Besides there are two pads prepared for soldering an external clock.


Features:

  • Atmel's ATxmega128A1U-AU integrated
  • All Ports available on pin rows (2.54mm pitch)
  • Dimensions: 69x69mm
  • All Pins are labled with the port names of the ATxmega128A1U-AU


Downloads:

The ATxmega128A1U Centipede can be ordered at our Shop

Personal tools