Difference between revisions of "ICnova ADB3000"
(→Downloads) |
|||
| Line 50: | Line 50: | ||
The {{PAGENAME}} can be ordered at our [http://shop.in-circuit.de/products/ICnova-CPU-Module/Entwicklungsboards/56/ICnova-ADB3000 Shop]. | The {{PAGENAME}} can be ordered at our [http://shop.in-circuit.de/products/ICnova-CPU-Module/Entwicklungsboards/56/ICnova-ADB3000 Shop]. | ||
Different Starter kits with [[:Category:ICnova CPU-Modules| ICnova CPU-Modules]] and Touchscreens are also available in the [http://shop.in-circuit.de/pages/37/Starterkits Shop] | Different Starter kits with [[:Category:ICnova CPU-Modules| ICnova CPU-Modules]] and Touchscreens are also available in the [http://shop.in-circuit.de/pages/37/Starterkits Shop] | ||
| + | |||
| + | == Suitable CPU Modules == | ||
| + | {{Modules|intro}} | ||
| + | {{Modules|header}} | ||
| + | {{Modules|g45fpga}} | ||
| + | {{Modules|footer}} | ||
== Software == | == Software == | ||
| − | + | {{Software}} | |
| − | + | ||
| − | + | ||
Revision as of 17:18, 30 September 2014
Contents |
Hardware
The ICnova ADB3000 is the development platform for your embedded Linux + FPGA projects. It is optimzed for the ICnova SAM9G45+XC3S700AN OEM Module but it also works with ICnova AP7000 OEM, ICnova AP7000 OEMplus, ICnova i.MX353 OEM and ICnova SAM9G45 OEM.
The ICnova ADB3000 has the following features:
- Compatible to all ICnova OEM modules
- Optimized for the SAM9G45+XC3S700AN OEM module
- All spare FPGA and ARM I/Os are available on pin headers
- Two high-speed connectors with 12 differential pairs each plus ground
- Integrated OpenOCD debugger and debug-UART for ARM via mini-USB connector
- All that is needed to program the ARM and the FPGA is an Ethernet cable and a USB port
- Power supply can be done using a wall power supply, a lab supply using banana jacks or USB
- Temperature range 0°C to +60°C
- Size: 200mm x 220mm
Interfaces ARM:
- 1x10/100 Base-T-Ethernet-Port
- 1xHigh-Speed-USB 2.0 Host port
- 1xHigh-Speed-USB 2.0 Device Port
- UART 0/1/2 and DBGUART on pin headers
- UART3 via mini USB plug
- SPI interface with 3x chip selects
- I²C interface (TWI)
- 1xµSD/MMC card slot
- 4xUser-LEDs
- Reset button
- 34 GPIOs on pin headers
- 1xConnector for a TFT-Touchscreen display
- 1xJTAG-interface (compatible with JTAGICE-mkII)
Interfaces FPGA:
- 222 I/Os on pin headers
- JTAG on pin header
- Low-Power / programming interface on pin header
- PROG-button for re-configuration
The ICnova ADB3000 can be ordered at our Shop. Different Starter kits with ICnova CPU-Modules and Touchscreens are also available in the Shop
Suitable CPU Modules
Software
All Modules provided by In-Circuit usally have a Buildroot based system preinstalled, so they can be used out of the box.
Login as "root" for which no password is set.
If you are new to kernel building please refer to First Steps with Buildroot.
The Board support packages listed in table above contain all sources required to build the linux image for the different combinations with the ICnova ADB3000.
If an older version of the BSP is needed please look at our Downloads section.
Generally the bootloaders on our modules are configured to loook for a bootable linux image on the SD-Card and only boot from flash if none is found.
