Difference between revisions of "Interface Modules"
(→USB-B UART Bridge CP2102) |
(→USB-B UART Bridge CP2102) |
||
Line 56: | Line 56: | ||
*IO: RX ( to connect with RX on the µC), TX (to connect with TX on the µC) | *IO: RX ( to connect with RX on the µC), TX (to connect with TX on the µC) | ||
*all Handshake signals are available on pin headers | *all Handshake signals are available on pin headers | ||
− | |||
<br/> | <br/> |
Revision as of 13:36, 9 February 2017
Contents |
USB-A UART Bridge CP2104
The USB-UART-Bridge connects UART components with an USB-Host. The Bridge generates a 3.45V Voltage from USB. This can be used to supply the microcontroller over a jumper (maximum 100mA@3.45V).
Features:
- Baud rate: 300Bit/sec up to 2MBit/sec
- GPIOs 0-3 are set to push/pull at delivery state! (so LEDs, TxEN and GPIO are working)
- Voltage-regulator: up to 100mA@3.45V
- LEDs: Power, RX and TX
- IO: RX ( to connect with RX on the µC),TX (to connect with TX on the µC), GND, VCC
- Size: (LxWxH)(mm): 52.0 x 17.0 x 5.2
Downloads:
- Driver: CP201x Driver
- Datasheet: Datasheet USB-A UART Bridge CP2104
- Schematic: Schematic USB-A UART Bridge CP2104
The USB-A UART Bridge CP2104 can be ordered at our Shop
USB-A UART Bridge CP2102
The USB-UART-Bridge connects UART components with an USB-Host. The Bridge generates a 3.3V Voltage from USB. This can be used to supply the microcontroller over a jumper (maximum 100mA@3.3V).
Features:
- Baud rate: 300Bit/sec up to 1MBit/sec
- Voltage-regulator: up to 100mA@3.3V
- LEDs: Power, RX and TX
- IO: RX ( to connect with RX on the µC),TX (to connect with TX on the µC), GND, VCC
- Size: (LxWxH)(mm): 45.0 x 15.0 x 5.2
Downloads:
- Driver: CP201x Driver
- How to install drivers for CP2102 (german)
- Datasheet: Datasheet USB-A UART Bridge CP2102
- Schematic: Schematic USB-A UART Bridge CP2102
The USB-A UART Bridge CP2102 can be ordered at our Shop
USB-B UART Bridge CP2102
The USB-UART-Bridge connects UART components with an USB-Host. The Bridge generates a 3.3V Voltage from USB ( maximum 100mA@3.3V).
Features:
- Baud rate: 300Bit/sec up to 1MBit/sec
- Voltage-regulator: up to 100mA@3.3V
- LEDs: RX and TX
- IO: RX ( to connect with RX on the µC), TX (to connect with TX on the µC)
- all Handshake signals are available on pin headers
Downloads:
- Driver: CP2102 CP201x Driver
- How to install drivers for CP2102 (german)
- Datasheet: Datasheet USB-B UART Bridge CP2102
- Schematic: Schematic USB-B UART Bridge CP2102
The USB-B UART Bridge CP2102 can be ordered at our Shop
USB-RS485-Bridge
Downloads:
- Driver: VCP Drivers
- Datasheet: Datasheet USB RS485 Bridge
- Schematic: Schematic USB RS485 Bridge
The USB RS485 Bridge can be ordered at our Shop