Difference between revisions of "DW1000 Anchor"
From InCircuit
(→Downloads) |
(q) |
||
Line 36: | Line 36: | ||
* If a TAG is inside a secure distance of 2 meter, the relay is triggered | * If a TAG is inside a secure distance of 2 meter, the relay is triggered | ||
* Fix HF-setup (channel, band width, transmitting power) | * Fix HF-setup (channel, band width, transmitting power) | ||
+ | |||
+ | |||
+ | '''Working with the demo-firmware command mode''' | ||
+ | |||
+ | * Connect the {{PAGENAME}} to your PC via RS485 (e.g. [[Interface_Modules#USB-RS485-Bridge|USB-RS485-Bridge]]) | ||
+ | * Connect VCC (9-48 V) and GND to {{PAGENAME}} | ||
+ | * Start a terminal program (e.g. PuTTY, HTerm, Hyperterminal, ...) with 57600 baud and 8N1 | ||
+ | * After opening the connection type "m" and press <Enter> once to display the menu | ||
+ | C)han:5 X)Str:27.5 P)ol:On D)ist:2.0 T)ableOut:Y R)eload S)tore Q)uit | ||
+ | > | ||
+ | |||
+ | <br/> | ||
+ | '''Available commands:''' | ||
+ | cX | ||
+ | * set channel to X. (Valid values: 1,2,3,4,5,7) | ||
+ | xYYZ | ||
+ | * set tx power to YY.Z dB (Range 0 to 33.5 steps of 0.5) | ||
+ | r | ||
+ | * reload last stored values from eeprom | ||
+ | s | ||
+ | * store current configuration to eeprom (The F option is not stored and reset on USB disconnect) |
Revision as of 11:52, 30 May 2017
Contents |
new page under construction
Hardware
Anchor for Ranging / RTLS applications with radino32 DW1000 Ultra Wide Band module.
Features:
- radino32 DW1000 module
- Integrated UWB antenna
- Vin 9-48V DC
- Enclosure IP 65
- RS485 Interface for data and setup
- 1x Relay 10A/250VAC, NC/NO-function switchable by jumper
- Connection: RS485(A/B/GND), Vin(9-48V), GND, 2xRelay
Downloads
- Datasheet: Datasheet DW1000 Anchor
- Schematic: Schematic DW1000 Anchor
Software
The DW1000 Anchor will be shipped with a closed source demo-firmware.
Functionality of demo-firmware
- Shows data of received Tags on RS485-interface in a readable format:
- TAG-ID, distance, signal strength.
- If a TAG is inside a secure distance of 2 meter, the relay is triggered
- Fix HF-setup (channel, band width, transmitting power)
Working with the demo-firmware command mode
- Connect the DW1000 Anchor to your PC via RS485 (e.g. USB-RS485-Bridge)
- Connect VCC (9-48 V) and GND to DW1000 Anchor
- Start a terminal program (e.g. PuTTY, HTerm, Hyperterminal, ...) with 57600 baud and 8N1
- After opening the connection type "m" and press <Enter> once to display the menu
C)han:5 X)Str:27.5 P)ol:On D)ist:2.0 T)ableOut:Y R)eload S)tore Q)uit >
Available commands:
cX
- set channel to X. (Valid values: 1,2,3,4,5,7)
xYYZ
- set tx power to YY.Z dB (Range 0 to 33.5 steps of 0.5)
r
- reload last stored values from eeprom
s
- store current configuration to eeprom (The F option is not stored and reset on USB disconnect)