Difference between revisions of "Interface Modules"
(→RS232(DTE)-UART-Bridge) |
(→RS232(DCE)-UART-Bridge) |
||
Line 177: | Line 177: | ||
*Datasheet: [[Media:305000029A_RS232(DCE)-UART-Bridge.pdf | Datasheet RS232(DCE)-UART-Bridge]]<br/><br/> | *Datasheet: [[Media:305000029A_RS232(DCE)-UART-Bridge.pdf | Datasheet RS232(DCE)-UART-Bridge]]<br/><br/> | ||
− | The USB-B-RS232 Bridge can be ordered at our [ | + | The USB-B-RS232 Bridge can be ordered at our [https://www.in-circuit.de/product-category/zubehoer/ Shop] |
<div style="clear:both"></div> | <div style="clear:both"></div> | ||
<br/><br/> | <br/><br/> |
Latest revision as of 13:47, 29 July 2023
Contents |
[edit] USB-A UART Bridge CP2104
The USB-UART-Bridge connects UART components with an USB-Host. The Bridge generates a 3.45V Voltage from USB. This can be used to supply the microcontroller over a jumper (maximum 100mA@3.45V).
Features:
- Baud rate: 300Bit/sec up to 2MBit/sec
- GPIOs 0-3 are set to push/pull at delivery state! (so LEDs, TxEN and GPIO are working)
- Voltage-regulator: up to 100mA@3.45V
- LEDs: Power, RX and TX
- IO: RX ( to connect with RX on the µC),TX (to connect with TX on the µC), GND, VCC
- Size: (LxWxH)(mm): 52.0 x 17.0 x 5.2
Downloads:
- Driver: CP210x Driver
- Datasheet: Datasheet USB-A UART Bridge CP2104
- Schematic: Schematic USB-A UART Bridge CP2104
The USB-A UART Bridge CP2104 can be ordered at our Shop
[edit] USB-A UART Bridge CP2102
The USB-UART-Bridge connects UART components with an USB-Host. The Bridge generates a 3.3V Voltage from USB. This can be used to supply the microcontroller over a jumper (maximum 100mA@3.3V).
Features:
- Baud rate: 300Bit/sec up to 1MBit/sec
- Voltage-regulator: up to 100mA@3.3V
- LEDs: Power, RX and TX
- IO: RX ( to connect with RX on the µC),TX (to connect with TX on the µC), GND, VCC
- Size: (LxWxH)(mm): 45.0 x 15.0 x 5.2
Downloads:
- Driver: CP210x Driver
- How to install drivers for CP2102 (german)
- Datasheet: Datasheet USB-A UART Bridge CP2102
- Schematic: Schematic USB-A UART Bridge CP2102
The USB-A UART Bridge CP2102 can be ordered at our Shop
[edit] USB-B UART Bridge CP2102
The USB-UART-Bridge connects UART components with an USB-Host. The Bridge generates a 3.3V Voltage from USB ( maximum 100mA@3.3V).
Features:
- Baud rate: 300Bit/sec up to 1MBit/sec
- Voltage-regulator: up to 100mA@3.3V
- LEDs: RX and TX
- IO: RX ( to connect with RX on the µC), TX (to connect with TX on the µC)
- all Handshake signals are available on pin headers
Downloads:
- Driver: CP210x Driver
- How to install drivers for CP2102 (german)
- Datasheet: Datasheet USB-B UART Bridge CP2102
- Schematic: Schematic USB-B UART Bridge CP2102
The USB-B UART Bridge CP2102 can be ordered at our Shop
[edit] USB UART Bridge ISO
The USB UART Bridge ISO connects UART components electrically isolated with an USB-Host.
Features:
- USB-B for PC plugging
- Baud rate: up to 3MBit/sec
- LEDs: RX and TX
- IO: RX (to connect with RX on the µC),TX (to connect with TX on the µC), GND and +5V on power supply of the µC
- Usable with and without flow control
Downloads:
- Driver: VCP Drivers
- Datasheet: Datasheet USB UART Bridge ISO
The USB UART Bridge ISO can be ordered at our Shop
[edit] USB-RS485-Bridge
The USB-RS485-Bridge connects RS485/422 components with an USB-Host. The Bridge generates it′s supply voltage from USB. A suitable enclosure is also available.
Features:
- Baud rate: up to 3MBit/sec
- LEDs: Power=orange, RX=red and TX=green
- IOs: RS485-A, RS485-B,GND
Downloads:
- Driver: VCP Drivers
- Datasheet: Datasheet USB RS485 Bridge
- Schematic: Schematic USB RS485 Bridge
- EU Conformity: EU Conformity USB RS485 Bridge
- Datasheet enclosure: Datasheet enclosure
The USB RS485 Bridge can be ordered at our Shop
[edit] USB-B-RS232 Bridge
The USB-B-RS232 Bridge connects RS232 components with an USB-Host.
Features:
- Baud rate: up to 250kBit/sec
- LEDs: Link, RX and TX
- RS232 male connector
- USB-B connector
Downloads:
- Driver: CP210x Driver
- Datasheet: Datasheet USB-B-RS232 Bridge
The USB-B-RS232 Bridge can be ordered at our Shop
[edit] RS232(DTE)-UART-Bridge
The RS232(DTE)-UART-Bridge shifts UART levels to RS232. The Bridge is powered with voltages of 3.3V to 5V.
Features:
- Baud rate up to 256kBit/sec
- Power supply 3.3V to 5V
- LEDs: RX, TX and for valid Data
- IO: RX, TX, GND, VCC
- all Handshake signals are available on pin headers
Downloads:
- Datasheet: Datasheet RS232(DTE)-UART-Bridge (german)
The USB-B-RS232 Bridge can be ordered at our Shop
[edit] RS232(DCE)-UART-Bridge
The RS232(DCE)-UART-Bridge shifts UART levels to RS232. The Bridge is powered with voltages of 3.3V to 5V.
Features:
- Baud rate up to 256kBit/sec
- Power supply 3.3V to 5V
- LEDs: RX, TX and for valid Data
- IO: RX, TX, GND, VCC
- all Handshake signals are available on pin headers
Downloads:
- Datasheet: Datasheet RS232(DCE)-UART-Bridge
The USB-B-RS232 Bridge can be ordered at our Shop