Interface Modules

From InCircuit
Jump to: navigation, search

Contents

USB-A UART Bridge CP2104

USB-A UART Bridge CP2104

The USB-UART-Bridge connects UART components with an USB-Host. The Bridge generates a 3.45V Voltage from USB. This can be used to supply the microcontroller over a jumper (maximum 100mA@3.45V).


Features:

  • Baud rate: 300Bit/sec up to 2MBit/sec
  • GPIOs 0-3 are set to push/pull at delivery state! (so LEDs, TxEN and GPIO are working)
  • Voltage-regulator: up to 100mA@3.45V
  • LEDs: Power, RX and TX
  • IO: RX ( to connect with RX on the µC),TX (to connect with TX on the µC), GND, VCC
  • Size: (LxWxH)(mm): 52.0 x 17.0 x 5.2


Downloads:

The USB-A UART Bridge CP2104 can be ordered at our Shop



USB-A UART Bridge CP2102

USB-A UART Bridge CP2102

The USB-UART-Bridge connects UART components with an USB-Host. The Bridge generates a 3.3V Voltage from USB. This can be used to supply the microcontroller over a jumper (maximum 100mA@3.3V).


Features:

  • Baud rate: 300Bit/sec up to 1MBit/sec
  • Voltage-regulator: up to 100mA@3.3V
  • LEDs: Power, RX and TX
  • IO: RX ( to connect with RX on the µC),TX (to connect with TX on the µC), GND, VCC
  • Size: (LxWxH)(mm): 45.0 x 15.0 x 5.2


Downloads:

The USB-A UART Bridge CP2102 can be ordered at our Shop



USB-B UART Bridge CP2102

USB-B UART Bridge CP2102

The USB-UART-Bridge connects UART components with an USB-Host. The Bridge generates a 3.3V Voltage from USB ( maximum 100mA@3.3V).


Features:

  • Baud rate: 300Bit/sec up to 1MBit/sec
  • Voltage-regulator: up to 100mA@3.3V
  • LEDs: RX and TX
  • IO: RX ( to connect with RX on the µC), TX (to connect with TX on the µC)
  • all Handshake signals are available on pin headers


Downloads:

The USB-B UART Bridge CP2102 can be ordered at our Shop



USB UART Bridge ISO

USB-A UART Bridge CP2104

The USB UART Bridge ISO connects UART components electrically isolated with an USB-Host.


Features:

  • USB-B for PC plugging
  • Baud rate: up to 3MBit/sec
  • LEDs: RX and TX
  • IO: RX (to connect with RX on the µC),TX (to connect with TX on the µC), GND and +5V on power supply of the µC
  • Usable with and without flow control


Downloads:

The USB UART Bridge ISO can be ordered at our Shop



USB-RS485-Bridge

USB-RS485-Bridge

The USB-RS485-Bridge connects RS485/422 components with an USB-Host. The Bridge generates it′s supply voltage from USB. A suitable enclosure is also available.


Features:

  • Baud rate: up to 3MBit/sec
  • LEDs: Power=orange, RX=red and TX=green
  • IOs: RS485-A, RS485-B,GND


Downloads:

The USB RS485 Bridge can be ordered at our Shop



USB-B-RS232 Bridge

USB-B-RS232 Bridge

The USB-B-RS232 Bridge connects RS232 components with an USB-Host.


Features:

  • Baud rate: up to 250kBit/sec
  • LEDs: Link, RX and TX
  • RS232 male connector
  • USB-B connector


Downloads:

The USB-B-RS232 Bridge can be ordered at our Shop



RS232(DTE)-UART-Bridge

RS232(DTE)-UART-Bridge

The RS232(DTE)-UART-Bridge shifts UART levels to RS232. The Bridge is powered with voltages of 3.3V to 5V.


Features:

  • Baud rate up to 256kBit/sec
  • Power supply 3.3V to 5V
  • LEDs: RX, TX and for valid Data
  • IO: RX, TX, GND, VCC
  • all Handshake signals are available on pin headers



Downloads:

The USB-B-RS232 Bridge can be ordered at our Shop



RS232(DCE)-UART-Bridge

RS232(DCE)-UART-Bridge

The RS232(DCE)-UART-Bridge shifts UART levels to RS232. The Bridge is powered with voltages of 3.3V to 5V.


Features:

  • Baud rate up to 256kBit/sec
  • Power supply 3.3V to 5V
  • LEDs: RX, TX and for valid Data
  • IO: RX, TX, GND, VCC
  • all Handshake signals are available on pin headers


Downloads:

The USB-B-RS232 Bridge can be ordered at our Shop



Personal tools