Difference between revisions of "DW1000 Tag"
From InCircuit
(→Downloads) |
(→Software) |
||
Line 36: | Line 36: | ||
* No power management: battery loader works, but the {{PAGENAME}} runs at full power | * No power management: battery loader works, but the {{PAGENAME}} runs at full power | ||
* Fix HF-setup (channel, band width, transmitting power) | * Fix HF-setup (channel, band width, transmitting power) | ||
+ | |||
+ | |||
+ | '''Working with the demo-firmware configuration menu''' | ||
+ | |||
+ | * Connect the {{PAGENAME}} to your PC | ||
+ | * Start a terminal program (e.g. PuTTY, HTerm, Hyperterminal, ...) with 57600 baud and 8N1 | ||
+ | ** [[radino/radino32_software#Install_virtual_com_port_driver|STM32 virtual com port driver]] need to be installed | ||
+ | * After opening the connection press <Enter> once to display the menu | ||
+ | A)ddr:0x1234 C)han:5 X)Str:27.5 R)eload S)tore F)orceMeas:N | ||
+ | > | ||
+ | |||
+ | <br/> | ||
+ | '''Available commands:''' | ||
+ | aYYYY | ||
+ | set address to 0xYYYY. (Vaild values: 0x0000 to 0xFFFF) | ||
+ | cX | ||
+ | set channel to X. (Valid values: 1,2,3,4,5,7) | ||
+ | xYYZ | ||
+ | set tx power to YY.Z dB (Range 0 to 33.5 steps of 0.5) | ||
+ | f | ||
+ | Toggle execute measurements. The module communicates with the anchors and prints out results. | ||
+ | r | ||
+ | reload last stored values from eeprom | ||
+ | s | ||
+ | store current configuration to eeprom (The F option is not stored and reset on USB disconnect) |
Revision as of 11:38, 30 May 2017
Contents |
new page under construction
Hardware
Tag for Ranging / RTLS applications with radino32 DW1000 Ultra Wide Band module.
Features:
- radino32 DW1000 module
- Integrated UWB antenna
- Integrated USB-Li-ion loader for 181650 batery
- microUSB connector for batery loading
- Transparent enclosure
- Accelerometer, 3-Axis (MMA7660FC)
- 3 free programmable LEDs
Downloads
- Datasheet: Datasheet DW1000 Tag
- Schematic: Schematic DW1000 Tag
Software
The DW1000 Tag will be shipped with a closed source demo-firmware.
Functionality of demo-firmware
- Communication with Anchor
- USB usable as configuration interface
- No power management: battery loader works, but the DW1000 Tag runs at full power
- Fix HF-setup (channel, band width, transmitting power)
Working with the demo-firmware configuration menu
- Connect the DW1000 Tag to your PC
- Start a terminal program (e.g. PuTTY, HTerm, Hyperterminal, ...) with 57600 baud and 8N1
- STM32 virtual com port driver need to be installed
- After opening the connection press <Enter> once to display the menu
A)ddr:0x1234 C)han:5 X)Str:27.5 R)eload S)tore F)orceMeas:N >
Available commands:
aYYYY
set address to 0xYYYY. (Vaild values: 0x0000 to 0xFFFF)
cX
set channel to X. (Valid values: 1,2,3,4,5,7)
xYYZ
set tx power to YY.Z dB (Range 0 to 33.5 steps of 0.5)
f
Toggle execute measurements. The module communicates with the anchors and prints out results.
r
reload last stored values from eeprom
s
store current configuration to eeprom (The F option is not stored and reset on USB disconnect)